1.Program instructions for Select Nissan Altima, Maxima, Sentra, Armada and Select Infiniti EX35, FX35, FX45, G35, QX45 Vehicles That Use FCC KBRASTU15(Fit for both 3 button and 4 button)

Please Read Carefully Before Trying!

If At Any Time You Make a Mistake, Start and Stop Your Car, Exit the Vehicle and Start Over. The Remote Can Be Only Programmed with a Master Key

 

1.sit in Car with Doors and Windows Closed.

 

2.lock Doors with Power Door Lock Switch on Driver's Door.

 

3.put in and Pull Out Key From Ignition Approx. 8 Times or Until You See the Hazard/turn Signal Lights Flash.

(older Models Lights May Flash After 4 or 5 Times) You Need to Do That in Less Then 10 Sec.

 

4.when Hazard Lights Flash (On 2005 and Newer Models the Gauge Needles May Jump a

Little Instead) , Put Key in Ignition and Turn to the Acc Position.(when Your Hazard

Lights Flash Your Car Is Sending a Signal to Be Received By the Remote)

 

 

5.press Lock Button on the New Remote Transmitter, Lights Should Flash Again.

If You Have 2 Remotes, 1 New and 1 Old or 2 New Ones, Please Continue with Steps 6 and 7.

If Not, Skip to End.

 

6.press Unlock Button on Driver's Door, Then Lock Button on Drivers Door, Lights Will Again Flash

 

7.press Lock Button on 2nd New or Old Remote. Lights Again Will Flash. You Are Done.

Exit Vehicle and Try Your Remote. It Will Not Work From Inside Car or with Key in Ignition.

 

 

Note: If Your Hazard Lights Flash After Inserting Your Key in and Out,

but You Can't Get the Remote to Program, You May Have a Dead Battery or the Wrong Remote.

If Instructions Do Not Work, Do It Again but When You Get in - Shut the Door, Buckle Seat

Belt and Lock Doors, Then Proceed to Putting Key in Ignition.

 

 

 

2.Programming Note for Ford Escape, Edge, Explorer, Expedition, F-150, F-250, Ranger and More (Fit for both 3 button and 4 button)

FCC ID:2L3T-15K601-AB , 8L3Z-15K601-AA, CWTWB1U345, CWTWB1U322, CWTWB1U311, CWTWB1U212

 

1.Close all doors and then open drivers door and press the UNLOCK button on drivers door panel while door is open and insert key in ignition.

2.Turn ignition from OFF to RUN 8 times within 10 seconds, with the 8th time ending in RUN. .Door locks will cycle to confirm programming mode.

3.Within 20 seconds press any button on first keyless remote. Door locks will cycle to confirm programming.

4.Within 20 seconds, press any button on second keyless remote. Door locks will cycle again to confirm programming.

5.Turn ignition to OFF. Locks will again cycle to indicate end of programming mode.

 

Correct procedure is as follows for European cars 433mhz :
1. Close all doors
2. put ket in ignition
3. turn the key from LOCK to ON position
4. cycle this rapidly eight times (from LOCK to ON position) within 10 seconds. Last cycle must end in ON position
5. car will confirm by locking and unlocking all doors.
6. within 7 seconds press any key on the transmitter. Car will confirm again.
7. repeat this for all transmitters (max. 4)
8. when finished, turn key to LOCK and car will confirm again.

 

 

 

 

 

3.Programming Note for Chrysler, Jeep, and Dodge (Fit for both 3 button and 4 button)

FCC ID:KOBDT04A OHT692427AA

 

1.Turn your car's engine off and turn the ignition to the key "run" position. Look closely at the ignition to determine the position.

2.Press and hold the "unlock" button on your functional key fob. Hold the button for five seconds, and then hold the "panic" button for one second (while still holding the "unlock" button).

3.Release both buttons simultaneously. Listen for a chime to signal that the key fob is in programming mode. If you don't hear the chime, start the procedure over.

4.Press and release the "lock" and "unlock" button on the functional key fob, and then simultaneously press and release the "unlock" button on the functional key fob and the key fob you want to program.

5.Listen for the chime to confirm that the key fob has been programmed. Turn the ignition to the "off" position to exit programming mode.

 

 

 

 

4.Programming Note for FCC ID: GQ43VT20T


1. Begin with the key out of the ignition.

2. OPEN and UNLOCK the DRIVER'S side door. CLOSE all other doors including the trunk.

3. Within 5 seconds INSERT the key into the ignition and PULL it out TWICE.

4. CLOSE then OPEN the DRIVER's side door TWICE.

5. Insert key INTO the ignition then REMOVE it.

6. CLOSE then OPEN the DRIVER's side door TWICE.

7. Insert the key INTO the ignition and LEAVE it in ignition.

8. CLOSE the DRIVER's side door.

9. Switch the ignition to ON then OFF.

10. REMOVE the key from ignition.

11. The door locks will now cycle to confirm the vehicle has successfully entered programming mode.

12. PUSH and HOLD the LOCK and UNLOCK button for 1.5 seconds on the first remote being programmed. As soon as you let go PUSH the LOCK button and HOLD it for 2 seconds.

13. The door locks will cycle to confirm successful programming of the remote. If you have any additional remotes to program repeat step 12 if you have no additional remotes proceed to step 14.

14. OPEN the DRIVER'S side door. Programming is now complete.

 

 

 

 

 

 

 

5.Programming Note for FCC ID: LHJ011

 

Factory Part No(s): 21997127

Also Compatible / Fully Interchangeable with Part No(s): 15132197, 15132198, 15186200, 15186201, 10377295, 15186203

Notes:

Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.

Keyless Entry System Memory Clearing Instructions are noted in the dark blue colored steps below.

Step-by-Step How To Programming Instructions:

1.      CLOSE all doors.

2.      INSERT key into the ignition.

3.      PRESS and HOLD the power UNLOCK button on driver’s side door panel. DO NOT release until instructed to do so in Step 5.

4.      Quickly TURN the Ignition ON, OFF, ON, OFF. (ON is the position just shy of starting your vehicle, OFF is the position where you can remove your key)

5.      RELEASE the power UNLOCK button on the Driver’s side door panel. The vehicle should respond by locking and unlocking automatically. (A) If locks cycle then CONTINUE to Step 6. (B) If the door locks begin to LOCK and UNLOCK BEFORE releasing the unlock button then the vehicle has not entered Programming Mode and you must START OVER. REMOVE key, OPEN door and RETURN to Step 1. (C) If the vehicle continues to LOCK and UNLOCK before releasing the UNLOCK button then there is a problem with the vehicle’s system and remotes must be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key too quick, too slow, there’s a problem with the vehicle’s system, or the vehicle is not equipped with a factory keyless entry system.

6.      HOLD the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30 seconds.

7.      Now REPEAT Step 6 for all additional remotes to be programmed,  including working ones.

8.      After Step 6 has been performed for all remotes TURN ignition to ON to exit programming mode.

9.      TURN ignition to OFF, and remove key.

10.  Test all remotes. Programming is complete.

11.  If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

 

 

 

 

6.Programming Note for FCC ID: UC60221 OR OUC60270

Factory Part No: 15913421, 20868672, 20952474, 22936098, 15913420, 20868852, 20669056, 22936099, 15913427, 22756462, 20869057, 15857840, 22951510, 15913415, 25839476, 20859053, 25836188, 20869963, 20952477, 22936101

Notes:

Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.Keyless Entry System Memory Clearing Instructions are noted in the dark blue colored steps below.

Procedure #1 (Vehicles with Driver Information Center Button – Located to the Right of Steering Wheel)

Step-by-Step How To Programming Instructions:

1.      INSERT key and TURN the ignition to ON (just shy of starting vehicle without cranking engine).

2.      PRESS vehicle information button until “PRESS TO RELEARN REMOTE KEY” is displayed.

3.      PRESS the Set/Reset Button (Button will have a checkmark) until “REMOTE KEY LEARNING ACTIVE” is displayed. Vehicle is now in Programming Mode.

4.      PRESS and HOLD LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will sound indicating successful programming.

5.      REPEAT Step 4 to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.

6.      To EXIT Pogramming Mode TURN ignition OFF & REMOVE key.

7.      Test all remotes. Programming is now complete.

8.      If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

Procedure #2 (Vehicles without Driver Information Center Button)

Step-by-Step How To Programming Instructions:

1.      INSERT key and TURN the ignition to ON (just shy of starting vehicle without cranking engine).

2.      PRESS the Trip Odometer Reset Button until “RELEARN REMOTE KEY” is displayed.

3.      PRESS and HOLD the Trip Odometer Reset Button for approximately 3 seconds until “REMOTE KEY LEARNING ACTIVE” displays. Vehicle is now in Programming Mode.

4.      PRESS and HOLD LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will sound indicating successful programming.

5.      REPEAT Step 4 to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.

6.      To EXIT Programming Mode TURN ignition OFF & REMOVE key.

7.      Test all remotes. Programming is now complete.

8.      If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

Verify that this important information is on the back of your remote before using these programming instructions.

 

 

 

7.Programming Note for FCC IDKOBUT1BT

 

Notes:

Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.

Keyless Entry System Memory Clearing Instructions are noted in the dark blue colored steps below.

Step-by-Step How To Programming Instructions:

1.      Close all doors.

2.      Insert key into the ignition.

3.      Press and hold the power UNLOCK button on driver’s side door panel. Do not release until instructed to do so in Step 5.

4.      Quickly turn the ignition ON, OFF, ON, OFF. (ON is the position just shy of starting your vehicle, OFF is the position where you can remove your key)

5.      Release the power unlock button on the driver’s side door panel. The vehicle should respond by locking and unlocking automatically. (A) If locks cycle then continue to Step 6. (B) If the door locks begin to lock and unlock BEFORE releasing the unlock button then the vehicle has not entered programming mode and you must start over. Remove key, open door and return to Step 1. (C) If the vehicle continues to lock and unlock before releasing the unlock button then there is a problem with the vehicle’s system and remotes must be programmed by a certified professional. If you are unable to get the door locks to cycle then you are turning the key too quick, too slow, there’s a problem with the vehicle’s system, or the vehicle is not equipped with a factory keyless entry system.

6.      Hold the LOCK and UNLOCK buttons on the remote at the same time until door locks cycle again. This could take up to 30 seconds.

7.      NOW repeat Step 6 for all additional remotes including working ones.

8.      After Step 6 has been performed for all remotes TURN ignition to ON to exit programming mode.

9.      Turn ignition to OFF, and remove key.

10.  Test all remotes. Programming is complete.

11.  If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

 

 

 

 

8.Programming Notes for chevy

Obtain all remote transmitters for this vehicle. This procedure will erase all previously programmed remotes. You must program all existing and new remotes that you wish to use on the vehicle at this time.

Procedure #1 (Vehicles with Driver Information Center Button – Located to the Right of Steering Wheel)

Step-by-Step How To Programming Instructions:

1.      INSERT key and TURN the ignition to ON (just shy of starting vehicle without cranking engine).

2.      PRESS vehicle information button until “PRESS TO RELEARN REMOTE KEY” is displayed.

3.      PRESS the Set/Reset Button (Button will have a checkmark) until “REMOTE KEY LEARNING ACTIVE” is displayed. Vehicle is now in Programming Mode.

4.      PRESS and HOLD LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will sound indicating successful programming.

5.      REPEAT Step 4 to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.

6.      To EXIT Pogramming Mode TURN ignition OFF & REMOVE key.

7.      Test all remotes. Programming is now complete.

8.      If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

Procedure #2 (Vehicles without Driver Information Center Button)

Step-by-Step How To Programming Instructions:

1.      INSERT key and TURN the ignition to ON (just shy of starting vehicle without cranking engine).

2.      PRESS the Trip Odometer Reset Button until “RELEARN REMOTE KEY” is displayed.

3.      PRESS and HOLD the Trip Odometer Reset Button for approximately 3 seconds until “REMOTE KEY LEARNING ACTIVE” displays. Vehicle is now in Programming Mode.

4.      PRESS and HOLD LOCK and UNLOCK buttons at the same time on first remote for approximately 15 seconds. An acoustic signal will sound indicating successful programming.

5.      REPEAT Step 4 to program additional remotes. You can have up to 8 programmed remotes for this vehicle. You must program ALL remotes including existing remotes.

6.      To EXIT Programming Mode TURN ignition OFF & REMOVE key.

7.      Test all remotes. Programming is now complete.

8.      If these programming instructions helped save you time and money, please consider sharing our website with friends and family so they can do the same.

 

 

9.Program Instructions for Toyota FCC ID:  HYQ12BBX

1. Start with the key out of the ignition, drivers door is open all others closed and 
    drivers door is unlocked.

2. Perform these steps within 5 seconds.
    A. Insert the key into the ignition(Do NOT Turn) Pull key out.
    B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
    A. Close then open the drivers door.
    B. Close then open the drivers door.
    C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
    A. Close then open the drivers door.
    B. Close then open the drivers door.
    C. Insert the key into ignition and leave it in ignition.
    D. Close the drivers door.
    E. Turn the ignition to ON (Do NOT Start) then back to OFF.
    F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically
    indicating successful entry into programming mode. 
    Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
    A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
    B. Immediately after letting go of the lock and unlock buttons,
        Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the     door locks should lock and then unlock once indicating successful programming. If
 the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
    C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door. Test all remotes. Programming is now complete.